Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of RADIFLAM B RV300K AE 375 BK - PBT-GF30 - RadiciGroup High Performance Polymers

Check here, which other Radiflam B datasheets, application examples or technical articles are available in Material Data Center

Características de processamento/físicas - Propriedades mecânicas - Propriedades térmicas - Propriedades elétricas - Outras propriedades - Diagrama

Any use of this information falls under the rules of our disclaimer.

Informação do produto

PBT flame retardant injection moulding grade. 30% glass fibre reinforced. Black colour.

Suitable for parts requiring fire retardancy along with high stiffness and good mechanical resistance. Rated V-0 according to UL-94.

Características de processamento/físicas	Valor	Unidade	Método de ensaio
ISO Dados
Contração após a moldagem, paralelo	0.4	%	ISO 294-4, 2577
Contração após a moldagem, perpendicular	0.9	%	ISO 294-4, 2577

Propriedades mecânicas	Valor	Unidade	Método de ensaio
ISO Dados
Módulo de tração	10600	MPa	ISO 527
Tensão na ruptura	135	MPa	ISO 527
Deformação na ruptura	2.5	%	ISO 527
Resistência ao impacto Charpy , +23°C	60	kJ/m²	ISO 179/1eU
Res. impacto Charpy c/entalhe, +23°C	10	kJ/m²	ISO 179/1eA

Propriedades térmicas	Valor	Unidade	Método de ensaio
ISO Dados
Temperatura de fusão, 10°C/min	225	°C	ISO 11357-1/-3
Temperatura de deflexão térmica, 1.80 MPa	205	°C	ISO 75-1/-2
Temperatura de deflexão térmica, 0.45 MPa	220	°C	ISO 75-1/-2
Temperatura de amolecimento Vicat, B	210	°C	ISO 306
Flamabilidade a espessura h	V-0	class	IEC 60695-11-10
Espessuras do tubo de teste	0.8	mm	-
Cartão Amarelo (yellow card) disponível	sim	-	-

Propriedades elétricas	Valor	Unidade	Método de ensaio
ISO Dados
Resistividade volumétrica específica	1E13	Ohm*m	IEC 62631-3-1
Índice comparativo de linha de fuga	250	-	IEC 60112

Outras propriedades	Valor	Unidade	Método de ensaio
Densidade	1670	kg/m³	ISO 1183

Diagrama

Características

Processamento

Moldagem por injeção

Forma de entrega

Granulado, Negro

Aditivos

Desmoldante

Características especiais

Retardante de chama, Estável contra o calor

Disponibilidade regional

América do Norte, Europa, Ásia Pacífico, America Centra e do Sul, Oriente/África

Outras informações

Moldagem por injeção

The material is delivered in moisture-proof packaging. It is important to dry the material prior to processing: maximum recommended water content is 0.02%. Typical conditions with a desiccant drier: temperature 120 ° C, dew point -40 ° C or below, time 2-4 h or more. Avoid excessive shear rates and high thermal stresses for better processing. Special care must be taken to avoid moisture absorption and contamination with other polymers when adding regrind material. Colour variation and mechanical properties reduction may occur and should always be carefully monitored.

Injection Molding Processing Parameters

Melt Temperature	Mold Temperature	Injection Speed
250 - 280°C	80 - 90°C	medium-high

Disclaimer

Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.

Created: Source: www.materialdatacenter.com

Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.